澳门十大信誉赌场排名-线路检测_欢迎您

  • <table id="swwsu"></table>
  • <table id="swwsu"><rt id="swwsu"></rt></table>
    <td id="swwsu"><option id="swwsu"></option></td>
  • <table id="swwsu"></table>
    Homebrew How-To's - Hambleton Bard
    Homebrew How-To's - Hambleton Bard

    Turbo yeast instruction for making alcohol

    Home brew Turbo Yeast - Typical instructions for making alcohol (moonshine) wash for either home distilling or treatment with essences.

     

    turbo yeast alcohol

    Start: Adding water

    1. Add a small amount of hot water to your 30 litre (or more) fermenter, enough to dissolve the sugar. Typically 5-10 litres.

    Note: Be careful here if you have a glass fermenter, you can't add too hot water. Best is to use a 30 litre or larger plastic bucket or fermenter.

     

    Adding sugar to your homebrew wash

    2. Add standard white sugar (or brewing sugar = dextrose mononydrate, but remember you need to add 10% more dextrose to compensate for the water bound in the sugar). Usually 6 kgs (moderate alcohol turbo yeast) or 8 kgs (high alcohol turbo yeast). 

    Note: It is important to add the sugar into the water and not the other way around as it is easier to dissolve it this way. 

    3. Mix well, make sure all is dissolved before you proceed.

     

    Topping up with water

    4. Top up with cold (or lukewarm) water to final volume, usually 25 litres. Check temperature, should now be ideally 25-30 C (not higher). If OK, then add the sachet of turbo yeast.

    Note: The temperature is usually fine here even if you don't fine tune it. If you add hot tap water in instruction 1, that might be up to 50-60 C but after adding 6-8 kgs of room tempered sugar, you have taken down the temperature at least 10C, probably more. Then after topping up with cooler water, you will end up with the perfect temperature (aim for 25C, that is a good start for all turbo's).

    The alcohol fermentation

    5. Leave to ferment in room temperature or a bit higher (20-25C is ideal). Fermentation time varies with the type of turbo yeast and it can be anything from 24 hours to 5-7 days.

    Note: Best result is achieved when temperature is slightly elevated, say around 22-24C AND fairly constant. It is not good to place fermenter near a thermostatic heater which goes on/off, or near a window you might open etc. If you want to use heaters, you can use heatpads and heatbelts, but avoid using an immersion heater as it can become very hot when it is switched on and it may kill off yeast cells around it.

    Activated carbon (charcoal) treatment, using finings etc

    6. When fermentation is over, rack off (use a syphon to transfer the liquid into another vessel and leave the thick sediment behind so you can discard that) before you proceed to use your wash. At this stage you can add finings to improve your result, you can also add liquid activated carbon which needs to be in immersion for 24 hours or more for best result (removes off-flavours).

    Link to us!

    Do you like our products? Please link to us!.

    Bulldog Master Brewer
    [Jan 25, 2018] Bulldog Master Brewer
    Bulldog Beer Yeast
    [April 5, 2017] Bulldog Beer yeast, 10g and 500g
    Alcotec Wine Finings
    [March 30, 2017] Alcotec ExtraKlar Finings
    Bulldog Sparger

    [February 6, 2017] Bulldog Sparger
    Alcotec Carbon Turbo
    [February 6, 2017] Alcotec Carbon Turbo
    DoubleSnake Carbon Turbo
    [February 6, 2017] DoubleSnake Carbon Turbo
    Puriferm Carbon Turbo
    [February 6, 2017] Puriferm Carbon Turbo
    [November 21, 2016] We are now ISO9001

     

    ?

    澳门十大信誉赌场排名